RESEARCH PAPER
Improvement in Mechanical Properties and Wear Resistance of the Nano Composite PMMA / Hydroxyapatite - Zirconia (HA-ZrO2) by Atmospheric Plasma
 
More details
Hide details
1
Department of Physics, College of Education, University of Al-Mustansiriyah, Baghdad, IRAQ
2
Department of Physics, College of Science, University of Baghdad, Baghdad, IRAQ
3
Department of Medical Physics, College of Science, University of Karkh for Science, Baghdad, IRAQ
Publish date: 2018-11-02
 
Eurasian J Anal Chem 2018;13(5):em69
KEYWORDS:
ABSTRACT:
In this paper, Nano composite (HA-ZrO2) was prepared in an effective mechanical mixing method. The calcination and reaction of the powder were done at (1200 °C) for (3 hours). Obtained samples were examined for the wear test of before and after plasma treated at 3 minutes (5, 10 and 15 min.) for the load (10 N.) under constant pressure and rotation number (2950 rive/min.) using a device (Pin - on - Disc). The Dielectric Barrier Discharge (DBD) Plasma was used under atmospheric pressure to improve the obtained samples. The results showed a significant improvement in hardness values and increased wear coefficient values after the treatment by plasma. That is, the higher the wear and tear coefficient, the more resistant the material will be to the resistance to corrosion and breakdown after plasma treatment.
 
REFERENCES (13):
1. Tudoran CD. Simplified portable 4 MHz RF plasma demonstration units. J Physics: Conference Series. 2009;182:012034. https://doi.org/10.1088/1742-6....
2. Anghel SD. Generation and Electrical Diagnostic of an Atmospheric-Pressure Dielectric Barrier Discharge. IEEE Trans. Plasma Sci. 2011;39:871–876. https://doi.org/10.1109/TPS.20....
3. Anghel SD. Generation and investigation of a parallel-plate DBD driven at 1.6 MHz with flowing helium. J. Electrost. 2011;69:261–264. https://doi.org/10.1016/j.elst....
4. Tanaka K, Taura A, Ge S-R, Takahara A, Kajiyama T. Macromolecules. 1996;29:3040–3042. https://doi.org/10.1021/ma9513....
5. Kawaguchi D, Tanaka K, Kajiyama T, Takahara A, Tasaki S. Macromolecules, 2003;36:6824–6830. https://doi.org/10.1021/ma0341....
6. Kajiyama T, Tanaka K, Takahara A. Macromol Symp. 2003;192:265–270. https://doi.org/10.1002/masy.2....
7. Cooper S, Visser S, Hergenrother R, Lamba N. Polymers. In Biomaterials Science: An Introduction to Materials in Medicine, B. Ratner, A. Hoffman, and F. Schoen, Eds., 2004:67– 80, Elsevier Academic, 2nd edition.
8. Nagao D, Kinoshita T, Watanabe A, Konno M. Fabrication of highly refractive, transparent BaTiO3/poly(methyl methacrylate) composite films with high permittivities. Polymer International, 2011:60(8):1180–1184. https://doi.org/10.1002/pi.305....
9. Lim KF, Muchtar A, Mustaffa R, Tan CY. Synthesis and Characterization of Hydroxyapatite – Zirconia Composites for Dental Applications. Asian Journal of Scientific Research 2014;7(4):609–615. https://doi.org/10.3923/ajsr.2....
10. Picconi C, Maccauro G. Zirconia as Ceramic Biomaterials. Biomaterials 1999;20:1–25. https://doi.org/10.1016/S0142-....
11. Abbas MK, Ibrahim IK, Naim IS. Effect of thermal coefficients on mechanical properties and wear resistance to a compound material based on aluminum. Journal of Engineering and Technology2011;12:2011.
12. Hassan AM, Mayyas AT, Mohammed AA, Hayajneh T. Wear Behavior of AL – Cu and AL – Cu / Sic Components Produced by Powder Metallurgy, Springer Science + Business Media, Published online 24 June. 2008:5368–5375.
13. Gul F, Acilar M. Effect of the Rein for Cement Volume Fraction on the Dry Sliding Wear Behavior of AL – 10 Si / Si Cp Composites Produced by Vacuum Infiltration Technique. Composites Science and Technology 2004;64:1959–1970. https://doi.org/10.1016/j.comp....
eISSN:1306-3057